ElektroPhysik 80-648-0101 MikroTest NIFE50M 6 Banana Gauge, Automatic Coating Thickness Gauge MIK/010800, 0-2 mils



Price: $ 1,900.00

ElektroPhysik MikroTest Banana Gauge, Magnetic Coating Thickness Gauge
Banana Gauge
11 different analog models available for every application
Suitable for measurement on curved surfaces

The MikroTest Banana Gauge is the most widely used coating thickness gauge in the world over the last 40 years. The MikroTest Banana Gauge complies with the highest technical standards of all analogue magnetic coating thickness gauges. This magnetic coating thickness gauge works on the magnetic attraction principle to measure all non-magnetic coatings on steel and galvanic nickel on steel.

The MikroTest is supplied in 11 different models to be suitable for every requested application. The balanced measuring system ensures accurate readings at any angle: horizontal, vertical and overhead. Also, the gauge allows measurements on curved surfaces. It is also able to provide you with precise measurements in tubes and on round parts due to the automatic operation.

The measurement of the coating thickness is based on magnetic attraction. The attractive force is related to the distance between a permanent magnet and a steel substrate. This distance represents the thickness of the coating under measure. The magnet is lifted from the surface by means of a spring connected to the magnet arm. The force needed to lift the magnet is directly related to the angle of rotation of the torsion spring. This measuring principle is also especially suited for electroplated nickel on copper, aluminum and other non-ferrous metals. This measurement principle ensures fully automatic measurement where no power supply or calibration is required.

MikroTest FM 5 Gage, Coating Thickness, 0 to 40 mils

  • New Part #: 80-638-0101
  • Old Part #: MIK/010100
  • NSN: 5220-12-327-2245


line
Kit Contents
line

  • MikroTest gauge
  • Hand strap
  • Plastic carrying case
  • Operating instructions


line
Features
line

  • Mils Models Include a NIST traceable calibration certificate, Micron Models include factory "works" certificate
  • Highest accuracy with simplest operation
  • No calibration required
  • Simple set-up and measurement
  • All gauges operate without power or battery
  • One point measurement
  • Metal Housing provides protection from mechanical shocks
  • Metal Housing and measuring system is resistant to solvents
  • Automatic models control realease of magnet for highest accuracy and repeatability


line
Specifications
line

Ambient Temperature-20 C - 100 C
Conforming StandardsDIN EN ISO 2178, DIN 50 982, ASTM B 499, E 376, D 1186, G 12, B 530, BS 5411, ISO 2361
DimensionsGauge: 215 mm x 55 mm x 29 mm Plastic carrying case: 235 mm x 185 mm x 46 mm
WeightCase incl. gauge approx. 560 g
Calibration ShimsHere are the two technical reasons why you cannot use plastic shims/foils plus zero plate to check calibration of MikroTest:
1. All Plastic Shims/Foils have a certain prestress which has the effect that they are slightly bent when the magnet lifts off and this effect is similar to the effect of a spring will cause inaccurate readings
2. The Plastic Shims/Foils have a certain electrostatic charge which also causes inaccurate readings.


line
Demo Video
line

  1. Adjust dial to value higher than the expected thickness
  2. Place gauge on surface to be measured
  3. Press button on bottom of handle take make the magnet adhere to surface
  4. Slowly turn wheel backwards until you hear a click and the magnet lifts
  5. Read thickness value


line
Models
line

TypeRangeTypical ApplicationTolerance
GM
G
4 mils
100 micron
Electroplating and Paint on Steel 1 m or 5% of reading
FM
F
40 mils
1000 micron
Paint On Steel 5 m or 5% of reading
S3M
S3
8 - 120 mils
0.2 - 3 mm
Enamel, Paint on Steel5% of reading
S5M
S5
20 - 200 mils
0.5 - 5 mm
Enamel, Paint on Steel5% of reading
S10M
S10
0.1 - 0.4 inches
2.5 - 10 mm
Enamel, Paint on Steel5% of reading
S20M
S20
0.3 - 0.8 inches
7.5 - 20 mm
Enamel, Paint on Steel5% of reading
Ni50M
Ni50
2 mils
50 micron
Electroplated Nickel on Non-Ferrous (1 m + 5% of reading)
Ni100M
Ni100
4 mils
100 micron
Electroplated Nickel on Non-Ferrous (1 m + 5% of reading)
NiFe50M
NiFe50
2 mils
50 micron
Electroplated Nickel on Steel (2 m + 8% of reading)

TypeMin SurfaceMin RadiusMin Base Thickness
GM
G
20 mm5 mm convex / 25 mm concave0.5 mm
FM
F
30 mmmm convex / 25 mm concave0.5 mm
S3M
S3
30 mm15 mm convex / 25 mm concave1.0 mm
S5M
S5
50 mm15 mm convex / 25 mm concave1.0 mm
S10M
S10
50 mm15 mm convex / 25 mm concave2.0 mm
S20M
S20
100 mm100 mm convex / 150 mm concave7.0 mm
Ni50M
Ni50
15 mm5 mm convex / 25 mm concave-
Ni100M
Ni100
15 mm5 mm convex / 25 mm concave-
NiFe50M
NiFe50
20 mm10 mm convex / 25 mm concave0.5 mm


line
High Temperature Option
line

An Optional High Temperature Kit is offered (MK-HT) for using MikroTest models on surface temperatures up to 212F (100C). It can also be used on surface temperatures up to 572F (300C), but the MikroTest must be limited to less than 5 seconds of surface contact or damage will result. The MK-HT Kit consists of aluminum feet and sensor prism.


Order Online
Check the items you would like to order then click "Add To Cart". Items typically ship within 1 Week
Product Price
ElektroPhysik 80-648-0101 MikroTest NIFE50M 6 Banana Gauge, Automatic Coating Thickness Gauge MIK/010800, 0-2 mils $1,900.00
Accessories Price
NISTCAL NIST Traceable Calibration Certificate (Per Probe Ordered) $100.00
MK-HT High Temperature Kit for Mikrotest, includes Aluminum Feet and Sensor Grommet - MIK/070870 $125.00

 



 
 

Powered by Marctin Web Architecture